Fundamental Plumber Guide for Installing a Bathtub
Fundamental Plumber Guide for Installing a Bathtub
Blog Article
What're your ideas on Installing A Bathtub?
Setting up a bath tub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is likewise a moderately tough job. If the old bathtub is conveniently available, the task can relocate speedily; if you need to open up a wall surface to get rid of the old tub and also place the new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the new one. See to it you have actually certified yourself for the job as well as are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed task, it is better to consider utilizing one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This post will certainly assist you mount a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and also don't need to change the setup of your previous water pipes.
Your devices and also product list must comprise the following:
Planning for the Setup
To start with, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be rather problematic because of the restricted access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression join; then do the very same for the other tap.
Switch on the supply of water as well as examine all joints as well as new pipework for leakages as well as tighten them if essential. Fill up the tub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, repair the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has been used at least when as this will certainly resolve it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Safeguard the faucet in position with the producer given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind needs to be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to break an inflexible seal, causing the water to permeate the wall between the bath and also the tiling, causing complications with wetness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can crack rather early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article about Installing A Bathtub from someone on another web address. Appreciated our posting? Please share it. Help others discover it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Leaks? Contact us! Report this page